模具行业专业术语

Assembly line组装线, Layout布置图, Conveyer流水线物料板, Rivet table拉钉机, Rivet gun拉钉枪, Screw driver起子, Electric screw driver电动起子, Pneumatic screw driver气动起子, worktable 工作

OOBA开箱检查,fit together组装在一起, fasten锁紧(螺丝), fixture 夹具(治具),pallet栈板,barcode条形码,

barcode scanner条形码扫描仪,fuse together熔合,fuse machine热熔

机,repair修理,operator作业员,QC品管,supervisor 课长,ME制造工程师,MT制造技术,cosmetic inspect外观检查,inner parts inspect内部检查,thumb screw大头螺丝,lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车

personnel resource department人力资源部production department生产部门planning department企划部

QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床 planer |'plein miller铣床grinder磨床driller钻床linear cutting线切割

electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长

general manager总经理special assistant manager特助factory director厂长department director部长

deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group

leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply

oil擦油to file burr 锉毛刺

final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水

cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料

scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程

deficient manufacturing procedure制程不良n|氧化 oxidation |' ksi'dei scratch刮伤dents压痕

defective upsiding down抽芽不良defective to staking铆合不良mp|镶块 embeded lump|in'bed| |l

feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车

trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称

administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单

screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴

iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把

mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架

to mop the floor拖地to clean the floor扫地to clean a table擦桌子air

pipe 气管packaging tool打包机

packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷

major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头

slipped screwhead/shippery screw thread滑手speckle斑点

mildewed=moldy=mouldy发霉rust生锈

deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良

excesssive gap间隙过大inclusion杂质

grease/oil stains油污painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤

poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理safety安全cost成本

exposed metal/bare metal金属裸露lack of painting烤漆不到位quality品质delivery deadline交货期

engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管

die worker模工production, to produce生产equipment设备to start a press开机classification整理

stop/switch off a press关机regulation整顿cleanness清扫conservation清洁culture教养

qualified products, up-to-grade products良品waste废料board看板feeder送料机sliding rack滑料架

defective products, not up-to-grade products不良品defective product box不良品箱die change 换模

to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺

plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深

to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格

not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更

evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速

manufacture management制造管理abnormal handling异常处理production unit生产单位

lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程

operation procedure作业流程to revise, modify修订stage die工程模automation自动化

to switch over to, switch---to throw--over switching over切换to stake, staking, reviting铆合

engineering, project difficulty工程瓶颈add lubricating oil加润滑油shut die架模

shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊

vocabulary for stamping

冲压常词汇

stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机

rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动reset复位

to grip(material)吸料location lump, locating piece, block stop 定位块smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货

to return delivenry to. to send delinery back,to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收

to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角to collect, to gather收集failure, trouble故障statistics统计

demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具

to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板

easily damaged parts易损件standard parts标准件

breaking.(be)broken,(be)cracked 断裂

to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具

figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模

compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边

to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印

upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化

die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销

die plate, front board模板padding block垫块stepping bar垫条upper die base上模座

lower die base下模座upper supporting blank上承板upper padding plate blank上垫板

spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人

scond check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical

invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil

stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔fature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆

spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标

dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器

concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾

granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular

offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机

模具工程类

plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印

冲压名称类

extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量 五金零件类

inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套

模板类

top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模) feature die公母模female die母模(凹模) upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板 零件类

punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块

本文来源：https://www.bwwdw.com/article/9ohm.html